Description
- Item Type: RC Drones
- Item Name: Eachine TRASHCAN TC75
- Wheelbase: 75 mm / 2.95 inch
- Size: 98 x 98 x 36 mm / 3.86 x 3.86 x 1.42 inch
- Weight: 33 g (without Battery)
Specification:
| Motor | Mode: TC0803 15000KV Configu-ration: 9N12P Stator Diamter: 8 mm / 0.31 inch Stator Length: 3 mm / 0.12 inch Motor Dimension(Dia.*Len): 10.5 x 14.5 mm / 0.41 x 0.57 inch Weight(g): 2.2g No.of Cells(Lipo): 1S-2S |
| Flight controller | (Frsky version) CRAZYBEEF4 PRO FR Firmware target: CrazybeeF4FR (Flysky version) CRAZYBEEF4 PRO FS Firmware target: CrazybeeF4FS (DSM2/DSMX version) CRAZYBEEF4 PRO Firmware target: CrazybeeF4DX (No RX version) CRAZYBEEF4 PRO FR Firmware target: CrazybeeF4DX MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 3.5-8.7V) Built-in 6A(each) Blheli_S 4in1 ESC Dshot600 ready Frsky version Built-in SPI Frsky receiver with telemetry(D8/D16 switchable) Flysky version Built-in SPI Flysky receiver with telemetry(AFHDS/AFHDS2A switchable) DSM2/X Version built-in Serial-based DSM2/DSMX compatible satellite receiver No RX version need to add external Receiver Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 28A Current meter scale set to 1175 Built-in 5V 1A Buck / Boost with LC filter Built-in voltage detection BLHELI_S pass-through Ready Taillight LED Ready |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v) Current: 6A continuous peak 7A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.Hex Default protocol: DSHOT600 |
| Frsky NON-EU receiver Version | SPI BUS receiver Frsky D8/D16 switchable Compatible Non EU transmitter both D8 and D16 mode Channels: 8ch or 16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
| Flysky receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 300m Failsafe support |
| DSM2/DSMX receiver version | Serial bus receiver Protocol: DSM2/DSMX compatible Channels:6-9 (Depend on your radio) No ground interference ( Transmitter and receiver 1 m from the ground): 300m |
| PNP No RX version | No RX version support external serial-bus receiver like xm+, crossfire, S-FHSS etc. |
| VTX | Output power: 25~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Antenna: RG178 antenna Frequency: 5.8GHz 5bands 40 channels With Raceband Smart Audio ready Weight: 3g |
| CADDX EOS2 camera | 1/3″ CMOS Sensor 1200 TVL 2.1mm lens 16:9 Image size NTSC Global WDR Internal Synchronization |
| Lipo Battery | Capacity: 300mAh Voltage: 3.8v Continuous Discharge Rate: 40C Instantaneous discharge rate: 80C Size: 55mmx11.5mmx6.5mm Weight: 7.8g Connector: PH2.0 *Notes: Need 2pcs batteries for Series circuit |
Package Includes:
- PNP/ NO Receiver Version
- 1 x 75mm Brushless whoop Frame
- 1 x Crazybee F4 PRO FC no RX verion
- 4 x TC0803 KV15000 Motor
- 1 x 40mm propeller(4cw+4ccw)
- 1 x Caddx EOS2 camera
- 1 x 5.8G 40ch 25mw~200mw VTX
- 4 x 3.8v 300mah 40C/80C battery
- 1 x USB Lipo/LIHV Charger
- 1 x Propeller disassemble tool
- 1 x LED board
- 1 x Screwdriver
- 1 x XT30 wire
- 1 x Bag
BNF Version:
- 1 x 75mm Brushless whoop Frame
- Option 1: 1 x Crazybee F4 PRO FC built-in Frsky NON-EU receiver
- Option 2: 1 x Crazybee F4 PRO FC built-in Flysky AFHDS and AFHDS-2A Switchable receiver
- Option 3: 1 x Crazybee F4 PRO FC built-in DSM2/DSMX receiver
- 4 x TC0803 KV15000 Motor
- 1 x 40mm propeller(4cw+4ccw)
- 1 x Caddx EOS2 camera
- 1 x 5.8G 40ch 25mw~200mw VTX
- 4 x 3.8v 300mah 40C/80C battery
- 1 x USB Lipo/LIHV Charger
1 x Propeller disassemble tool - 1 x LED board
- 1 x Screwdriver
- 1 x XT30 wire
- 1 x Bag
Estimated Delivery time 35-60 days.
U***r –
it fly good and stable even on 1S
A***A –
The article is as described it works correctly